Body Frame Making ServicesPT. Sinartech Multi Perkasa is a company engaged in the field of manufacturing construction based in Medan. Our company provides assembly and manufacturing services for body frames. The scope of work as follows:Design, Drawing, Manufacturing, Construction, Fabrication,
Clarifier Water Tank Manufacturing ServicesConstruction structure:Sewer pipe.Exhaust pipe.Pipe recycling.George Kent Flow meter or equivalent.Access spiral staircases, operating platforms and hand rails + sidewalks.Valves for water and mud sampling.Equipped with inlet, overflow, drainage and c / w
Boiler Feed Manufacturing Services for Water Tank CapFeature1. The receiving plant is mounted on the stand.2. Bronze floating type make-up valve.3. Stainless steel temperature gauge.4. Bronze the water measures the chicken with a 5/8 ukur red gauge glass line.5. Centrifugal boiler feed pump.6. The
Thermal Deaerator Making ServicesConstruction:Made of 8 mm SUS 304 stainless steel plate from all welded constructions.Equipped with a stainless steel tube sprayer.Equipped with an excess vacuum system.Equipped with a manhole.Equipped with a vacuum breaker and pressure reducing valve.All necessary
Development Services for Fuel Conveyor Boiler DistributionDimensions: 760 width x 600 height x 26m long (only to the site)Type: Scraper Conveyor (double deck)Chain: PC 4 "twin chain with 15,000 lbf breaking load, Scraper eachThird link, with high tensile bolts c / w Spring washer and double
Daily Fuel Tank Making ServicesFuel Tank Parts - The fuel tank or fuel tank serves to store the fuel needed by the engine when on the go, the fuel tank is made of thin steel plate with the inside coated with anti-rust.In the fuel tank there is a fuel sender gauge that serves to show the amount of
Back Pressure Vessel Making ServiceConstruction:The construction unit is welded.Fabrication of 10 mm boiler plates which are clogged with ends welded to the side.One (1) 450 mm him. manhole c / w cover.Supported on two (2) feet, one fixed and the other allows free movement during expansion of the
Shell & Fiber Conveyor Manufacturing ServicesShell & Fiber Conveyor at Palm Oil Processing Plant serves to distribute shells and fiber into the kitchen boiler for fuel. This screw model conveyor is 600 mm in diameter. Fuel Conveyor is placed at the top of the Boiler.ProcessGeneral layout
Services to Build a Kernel Bulking SiloConstruction design:Made from 6 mm plates & 9 mm ms from all welded ones built.Supported on steel structures with sufficient sized steel.The steel structure will also be built to support tracked mixed cyclones and cyclone shells.Angled bottom outlets are
Construction Services for Kernel Storage BinStorage Bin is a type of storage generally containing several storage spaces or slots. This is called a storage area in Warehouse Management. The storage area is the smallest space unit available in the warehouse. Therefore, the storage area describes the
Dry Kernel Conveyor Manufacturing ServiceConstruction Structure:Shell: 5 mm thick ms plate.Stiffener: 50 x 50 x 5 mm ms corner bars welded to the edges.End plate: 7 mm thick ms plate.Wear plate: 5 mm thick plate.Screw: ms plate 5 mm thick.Shaft: 50 mm him. solid round bar.Chute: Chute the
Prieumatic Dry Kernel Transport Manufacturing ServiceFollowing construction structure:Shell: 5 mm thick ms plate.Stiffener: 50 x 50 x 5 mm ms corner bars welded to the edges.End plate: 7 mm thick ms plate.Wear plate: 5 mm thick plate.Screw: ms plate 5 mm thick.Shaft: 50 mm him. solid round bar
Making Services of Wet Kernel ElevatorsConstruction Structure: The bottom and boot are made from a 6 mm thick ms plate, reinforced with a 50 x 50 x 5 mm ms corner and equipped with a 4 mm thick liner plate.The intermediate section composes a 5 mm thick plate reinforced with a 50 x 50 x 5 mm ms
Creation of Silo Kernel ServicesConstruction Structure:The shell is made of 5 mm thick MS plates and reinforced with 100 mm channels.The bottom cone is made of 7 mm thick plates.Column angle bar of 150 x 150 x 15 mm and supported by a rod angle of 75 x 75 x 7 mm.Internally equipped with circular
Services Build Wet Kernel ConveyorConstruction Structure:Shell: 5 mm thick ms plate.Stiffener: 50 x 50 x 5 mm mm welded to the corner bar edgeEnd plate & flange: 7 mm thick plate.Wear plate: 5 mm thick plate.Screw: ms plate 5 mm thick.Shaft: 50 mm him. solid round bar.Chute: Chute the
For more information please send me a message or contact us!
Please fill out your bio-data first to stay connected